What machine installation covers on site
Our machine installation service is focused on getting deep-hole drilling and boring equipment into position, connected correctly and ready for the next stage of commissioning. We work with manufacturers and engineering shops in Benoni, Johannesburg, Pretoria, Durban, Cape Town and Gqeberha, with support arranged from our Gauteng base.
Installation is more than placing a machine on the floor. These systems often need careful access planning, levelling, foundation checks, power and service checks, coolant line routing and a proper first alignment before any production work starts. In many workshops the biggest delays come from small details such as floor condition, access for lifting gear and where the coolant system sits, so we check those early.
- Site arrival planning and equipment offloading coordination
- Machine positioning and levelling
- Power and utility connection checks
- Coolant system positioning and pipe routing
- Initial alignment checks before handover
How the installation process runs
We start with a site review and a clear installation plan. That includes checking floor access, machine entry points, lifting requirements and the space needed around the unit for maintenance and operator movement. If the machine is going into a busy production area we also look at where material will move in and out, so the install does not block other work.
Once the machine is on site our technician works through the setup steps in a practical order. We verify position, level and connection points, then support the first start-up checks with the operator or supervisor present. If the equipment forms part of a wider production line, we coordinate with your team so the handover fits your schedule rather than stopping the whole shop.
- Pre-installation site discussion
- Delivery and access planning
- Positioning, levelling and connection setup
- Start-up checks and basic test runs
- Operator handover and next-step guidance
Setup details for deep-hole drilling and boring equipment
Deep-hole drilling and boring machines need accurate setup because small errors can affect hole quality, tool life and repeatability. We assist with setup optimisation after installation, including checks on alignment, tool holding, coolant delivery and the general arrangement around the work area. If the machine will be used for long runs or tight tolerances, that setup needs to be handled carefully from the start.
Our applications specialist and machine technician work with the site team to make sure the machine is ready for practical use, not just powered on. That can include checking the operator reach points, confirming access for routine cleaning, and setting up the machine so maintenance is not awkward later. In coastal areas like Durban and Gqeberha we also pay attention to moisture exposure and how the machine will be protected during idle periods.
- Alignment checks for the machine base and working position
- Tooling fitment support and first setup checks
- Coolant flow review and hose routing
- Practical access for daily cleaning and inspection
- Advice on workshop layout around the machine
Turnaround times and site coordination
Turnaround depends on the machine type, the site readiness and how much pre-installation preparation has been done. A workshop that has cleared floor space, arranged lifting access and confirmed utilities can move faster than a site still making structural changes. We will always give a realistic plan rather than promise a date that does not suit the conditions on the ground.
For Gauteng sites, especially Benoni, Johannesburg and Pretoria, we can usually coordinate install visits efficiently because the travel time is manageable. For Durban, Cape Town and Gqeberha we plan the visit properly so the team arrives with the right tooling and support items. If a site has load-shedding concerns, we also discuss how that affects commissioning, coolant circulation and the first start-up window.
- Simple installs may be completed in a single planned visit
- More involved setups may need return visits for commissioning or operator training
- Site readiness has a direct effect on turnaround
- Travel and scheduling are confirmed before work starts
Pricing approach for installation work
We price machine installation based on the actual scope of work. That means the type of machine, site location, access conditions, level of setup needed, and whether commissioning or training must be done at the same time. We do not work on guesswork because every workshop is different and the support needs can change from one installation to the next.
If a site only needs positioning and basic setup, the cost will differ from a full installation that includes alignment checks, coolant system service, production startup and operator training. We will first discuss what is needed, then quote on the agreed scope so there are no surprises once the machine is on site. The approach is straightforward and practical, which helps when budgets are under pressure.
Maintenance intervals after installation
Once installation is complete, the machine should not be left without follow-up. Early maintenance checks help confirm that alignment has held, coolant systems are behaving properly and there are no issues caused by settling or first-use wear. For most sites we recommend an early post-installation check after initial production running, then routine intervals based on use intensity.
Busy production shops, especially those running multiple shifts, often need more frequent inspection than a lighter engineering operation. Preventive maintenance can include alignment checks, coolant system service, fastener inspection and a review of tool condition. If your workshop runs through voltage dips or load-shedding, it is worth checking the machine after power interruptions too, because that is often when small faults show up.
- Early follow-up check after production start
- Routine alignment and coolant inspections
- Additional checks after power interruptions
- Maintenance interval adjusted to machine use and shift pattern
Who handles the work at Deephole
Our installation support is led from Benoni by Marius Jacobus van Rensburg, with a team that includes Ayanda Mokoena in sales engineering, Johan Smit in applications support, Noluthando Dlamini in service coordination, Francois du Plessis as machine technician, Leanne Naidoo in training and Sibusiso Khumalo for tooling support. That mix matters because installation is not only a technical job, it is also a coordination job.
Whether the installation is for a new production cell or a replacement machine, we keep the process clear and practical. You deal with people who understand deep-hole drilling work, from tooling selection through to production startup. If there is a problem during commissioning or the first few runs, we stay involved until it is sorted, not just handed off and forgotten.
Key facts
| Service type | On-site installation support for deep-hole drilling and boring equipment |
|---|---|
| Coverage area | Benoni, Johannesburg, Pretoria, Durban, Cape Town, Gqeberha and wider South Africa |
| Typical scope | Positioning, levelling, connection checks, alignment, commissioning support |
| Included support | Setup optimisation, operator handover and first-run assistance |
| Pricing basis | Quoted to site conditions, machine type and support scope |
| Follow-up | Post-installation maintenance and alignment checks available |
| Contact method | Enquiry form on the contact page |
